News

  • THE TYPE OF SIX/NINE MAIN MACHINE CURING PARTS

    THE TYPE OF SIX/NINE MAIN MACHINE CURING PARTS

    1每班开机前必须逐点检查各润滑部分,并按期对各齿轮箱、减速机补充润滑剂,必要时给于更换。 Before operating the main block making machine, each of the lubrication parts need to be checked one by one. The gear boxes and reduction devices need to supplement the lubricants timely, and be replaced if ne...
    Read more
  • Power required , land area, man power and lifetime of mould

    Power required , land area, man power and lifetime of mould

    POWER REQUIRED Simple production Line: approximately 110kW Per hourly power usage: approximately 80kW/hr Fully-automated production line: approximately 300kW Per hourly power usage: approximately 200kW/hr LAND AREA & SHED AREA For a Simple production Line, around 7,000 – 9,000m2is required wh...
    Read more
  • How to make it–Block Curing (3)

    How to make it–Block Curing (3)

    Low pressure Steam Curing Steam curing at atmospheric pressure at temperature of 65ºC in a curing chamber accelerates the hardening process. The main benefit of steam curing is the rapid strength gain in the units, which allows them to be placed in inventory within hours after they are molded. 2...
    Read more
  • How to make it   –Block Curing (2)

    How to make it –Block Curing (2)

    Natural Curing In countries where the climate is favorable, green blocks are moist cured at normal temperature of 20°C to 37°C (as in the South of China). This type of curing which at 4 days would normally give 40% of its ultimate strength. Initially, green blocks should be placed in a shaded ar...
    Read more
  • How to make it–Block Curing (1)

    How to make it–Block Curing (1)

    High pressure steam curing This method uses saturate steam at pressures ranging from 125 to 150 psi and temperature of 178°C. This method usually requires additional equipment such as an autoclave (kiln). The strength of high pressure cured concrete masonry units at one day age are equivalent to ...
    Read more
  • Some questions customers may ask ( block making machine)

    Some questions customers may ask ( block making machine)

    1. The differences between mould vibration and table vibration: In shape, motors of mould vibration are on both sides of the block machine, while the motors of table vibration are just under the moulds. Mould vibration is suitable for small block machine and producing hollow blocks. But it is exp...
    Read more
  • Application and characteristics of QT6-15 concrete block forming machine

    Application and characteristics of QT6-15 concrete block forming machine

    (1) Purpose: The machine adopts hydraulic transmission, pressurized vibration forming, and the vibration table vibrates vertically, so the forming effect is good. It is suitable for urban and rural small and medium-sized concrete block factories to produce all kinds of wall blocks, pavement blo...
    Read more
  • Advantages of Hercules block machine

    Advantages of Hercules block machine

    Advantages of Hercules block machine    1). Components of the block machine like face mix feeding box and base mix feeding box all can be detached from the main machine for maintenance and cleaning. 2). All the parts are designed to be easily changeable. Bolts and nuts design are used widely inst...
    Read more
  • Reuse of construction waste

    Reuse of construction waste

    With the continuous advancement of urbanization, there are more and more construction waste in recent years, which has brought trouble to the urban management department. The government has gradually realized the importance of resource treatment of construction waste; From another point of view, ...
    Read more
  • Daily inspection of equipment in the production line of non fired brick machine

    Daily inspection of equipment in the production line of non fired brick machine

    In order to ensure the normal operation of the equipment of the non fired brick machine production line, the following conditions must be met: Press the pressure control button to confirm that the reading of the output gauge installed on the pump body is “0″, and the current of the oi...
    Read more
  • The technical revolution of non fired brick machine drives the steady development of brick machine equipment industry

    The technical revolution of non fired brick machine drives the steady development of brick machine equipment industry

    The unburned brick machine equipment adopts the pressing and forming process of construction waste, slag and fly ash, with high compactness and initial strength. From the production of brick making machine, the automatic operation of distributing, pressing and discharging is realized. Equipped wi...
    Read more
  • Performance characteristics and development of non burning block machine

    Performance characteristics and development of non burning block machine

    The design of non burning block brick machine integrates the advantages of various models. The block machine not only integrates the characteristics of automatic block machine, but also quotes a number of new technologies and processes: 1. Design idea of non fired brick machine (non fired block b...
    Read more
123456 Next > >> Page 1 / 8
+86-13599204288
sales@honcha.com