+86-13599204288
News
-
Explain the process of a working line
Simple production line: The wheel loader will put different aggregates in the Batching Station, it will measure them to the required weight and then combine with the cement from cement silo. All of the materials will then be sent to the mixer. After being mix evenly, the belt conveyer will convey...Read more -
Application and Characteristics of QT6-15 Block Making Machine
(I) Application The machine adopts hydraulic transmission, pressure vibration forming, vertical directional vibration of shaking table, so the shaking effect is good. It is suitable for small and medium-sized concrete block factories in urban and rural areas to produce all kinds of wall blocks, p...Read more -
With the development of green building, block forming machine is becoming mature
Since the birth of the block forming machine, the state has paid more and more attention to the development of green buildings. At present, only some buildings in big cities can meet the national standards in China. The core content of green buildings is mainly what kind of wall materials can be ...Read more -
Servo brick machine is welcomed by the market
Servo brick machine is welcomed by the market for its good performance and wide range of products. The servo brick machine is controlled by the servo motor, which has high precision and fast response. Each motor is an independent unit and has no interference with each other. It overcomes the ener...Read more -
New permeable brick making machine: instructions for production environment of block brick machine and product characteristics
During the production of the new permeable brick making machine in winter, when the indoor temperature is low, the hydraulic station should be preheated and heated first. After entering the main screen, enter the manual screen, click Reset, and then click to enter the automatic screen to observe ...Read more -
Block machine equipment list
Equipments list: Ø3-compartment batching station ØCement silo with accessories ØCement scale ØWater scale ØJS500 twin shaft mixer ØQT6-15 block making machine ØPallet & block conveyor ØAutomatic stackerRead more -
THE TYPE OF SIX/NINE MAIN MACHINE CURING PARTS
1每班开机前必须逐点检查各润滑部分，并按期对各齿轮箱、减速机补充润滑剂，必要时给于更换。 Before operating the main block making machine, each of the lubrication parts need to be checked one by one. The gear boxes and reduction devices need to supplement the lubricants timely, and be replaced if ne...Read more -
Power required , land area, man power and lifetime of mould
POWER REQUIRED Simple production Line: approximately 110kW Per hourly power usage: approximately 80kW/hr Fully-automated production line: approximately 300kW Per hourly power usage: approximately 200kW/hr LAND AREA & SHED AREA For a Simple production Line, around 7,000 – 9,000m2is required wh...Read more -
How to make it–Block Curing (3)
Low pressure Steam Curing Steam curing at atmospheric pressure at temperature of 65ºC in a curing chamber accelerates the hardening process. The main benefit of steam curing is the rapid strength gain in the units, which allows them to be placed in inventory within hours after they are molded. 2...Read more -
How to make it –Block Curing (2)
Natural Curing In countries where the climate is favorable, green blocks are moist cured at normal temperature of 20°C to 37°C (as in the South of China). This type of curing which at 4 days would normally give 40% of its ultimate strength. Initially, green blocks should be placed in a shaded ar...Read more -
How to make it–Block Curing (1)
High pressure steam curing This method uses saturate steam at pressures ranging from 125 to 150 psi and temperature of 178°C. This method usually requires additional equipment such as an autoclave (kiln). The strength of high pressure cured concrete masonry units at one day age are equivalent to ...Read more -
Some questions customers may ask ( block making machine)
1. The differences between mould vibration and table vibration: In shape, motors of mould vibration are on both sides of the block machine, while the motors of table vibration are just under the moulds. Mould vibration is suitable for small block machine and producing hollow blocks. But it is exp...Read more
